Cross-compiling GTK+ over DirectFB v0.2

By | July 28, 2008


Intro

This guide is based in the wiki GTK on DirectFB for Embedded Systems from the DirectFB site, but it uses the latest packages available to this date. The first version of this guide used some unstable packages whilst this version uses only stable ones, but since I haven’t been  to test it properly this guide is not present in mentioned wiki. Hopefully, once this procedure becomes stable and tested a bit more, the wiki will be updated.

I tested this procedure in a STMicroelectronics ST40 processor (SH architecture). If you’re using this processor, this is the configuration I have:

  • Board: STB7109 cut 3.0, also called cocoref_gold_7109
  • Linux distribution: STLinux 2.2
  • DirectFB driver: stgfb-3.0_stm23_0008-4


Warnings

  1. This documentation assumes you already have DirectFB install in $PREFIX/usr. Change it accordingly to your installation.
  2. This documentation is still a work in progress, some steps of this procedure could be useless, ugly and/or dangerous
  3. The autotools are not very user-friendly when cross-compiling, thus, several configure files and Makefile (that are generated by the autotools) have to be edited by hand.
  4. GTK+ and all the packages underneath need a considerable amount of space and processor. If your embedded device provides a hard-drive/compact-flash or a big flash and supports hardware accelerated graphics you can use GTK+ without problems.


Requirements

Typically, when developing applications for an embedded system a cross-toolchain is needed. If you already have a cross-toolchain you don’t have to worry about building it yourself. Otherwise, a well known resource for building one is http://www.kegel.com/crosstool

When developing for embedded systems, there are very few Linux distributions or packages that contain all the required software for building GTK+, therefore you have to build everything from scratch.

The order in which the packages are compiled is important since some of them won’t compile without the others. The packages, their versions and the order used for building GTK+ are the following:

  • glib-2.15.4
  • atk-1.23.5
  • freetype-2.3.7
  • zlib-1.2.3
  • libxml2-2.6.30
  • fontconfig-2.6.0
  • libpng-1.2.29
  • cairo-1.6.4
  • pango-1.21.3
  • gtk+-2.12.11


Environment configuration

Suppose that the libraries will be installed in /opt/oe/STM/STLinux-2.2/devkit/sh4/target/usr/local ( /opt/oe/STM/STLinux-2.2/devkit/sh4/target is the root fs of the target) and that the cross-toolchain (compiler, linker…) is in your path.

Set the following environment variables that will make our life easier:

$ export PREFIX=/opt/oe/STM/STLinux-2.2/devkit/sh4/target/usr/local
$ export LD_LIBRARY_PATH=$PREFIX/lib
$ export PKG_CONFIG_PATH=$LD_LIBRARY_PATH/pkgconfig
$ export COMPILER=sh4-linux-gcc
$ export HOST=sh4-linux
$ export BUILD=i386-linux


Compiling the requirements


Glib 2.15.4

Edit the “configure” file:

Search for the texts “cannot run test program while cross compiling” and “cross-compiling”. Remove the following code that appe
ars a couple of lines below the searched texts:

{ (exit 1); exit 1; };

Configure, compile and install:

$ ./configure --build=$BUILD --host=$HOST --prefix=$PREFIX 
  --disable-largefile --disable-selinux --disable-gtk-doc --disable-man
$ make
$ make install


Atk 1.23.5

Configure, compile and install:

$ ./configure --host=$HOST --build=$BUILD --prefix=$PREFIX --disable-glibtest --disable-gtk-doc
$ make
$ make install


Freetype 2.3.7

Configure, compilie and install:

$ ./configure --host=$HOST --build=$BUILD --prefix=$PREFIX
$ make
$ make install


Zlib 1.2.3

Configure, compilie and install:

$ CC=$COMPILER ./configure --prefix=$PREFIX --shared
$ make
$ make install


libxml2 2.6.30

Configure, compilie and install:

$ ./configure --host=$HOST --build=$BUILD --prefix=$PREFIX --without-debug
$ make
$ make install


Fontconfig 2.6.0

Configure, compile and install:

$ ./configure --build=$BUILD --host=$HOST --prefix=$PREFIX 
  --with-freetype-config=$PREFIX/bin/freetype-config --enable-libxml2 --with-arch=sh4  
  --disable-docs
$ make
$ make install


libpng 1.2.29

Edit the “configure” file:

Set to ‘yes’ the following variable:

ac_cv_lib_z_zlibVersion=yes

Configure, compile and install:

$ ./configure --host=$HOST --build=$BUILD --prefix=$PREFIX
$ make
$ make install


Cairo 1.6.4

Configure, compile and install:

$ directfb_CFLAGS="-I$PREFIX/../include/directfb" 
  directfb_LIBS="$PREFIX/../lib/libdirectfb.so 
  $PREFIX/../lib/libdirect.so 
  $PREFIX/../lib/libfusion.so" 
  png_CFLAGS="-I$PREFIX/include" 
  png_LIBS=$PREFIX/lib/libpng12.so 
  FONTCONFIG_CFLAGS="-I$PREFIX/include/fontconfig" 
  FONTCONFIG_LIBS=$PREFIX/lib/libfontconfig.so 
  FREETYPE_CFLAGS="-I$PREFIX/include/freetype2" 
  FREETYPE_LIBS=$PREFIX/lib/libfreetype.so 
  ./configure --host=$HOST --build=$BUILD --prefix=$PREFIX 
  --enable-directfb=yes --without-x --disable-xlib 
  --disable-xlib-xrender --disable-win32 --enable-pdf=no 
  --enable-ps=no --enable-png
$ make
$ make install


Pango 1.21.3

Set to ‘true’ the following variables:

have_cairo=true
have_cairo_png=true
have_cairo_freetype=true

Configure:

$ GLIB_CFLAGS="-I$PREFIX/include/glib-2.0 -I$PREFIX/lib/glib-2.0/include" 
  GLIB_LIBS="$PREFIX/lib/libglib-2.0.so 
  $PREFIX/lib/libgmodule-2.0.so 
  $PREFIX/lib/libgobject-2.0.so 
  $PREFIX/lib/libfontconfig.so 
  $PREFIX/lib/libxml2.so 
  $PREFIX/lib/libfreetype.so" 
  CAIRO_CFLAGS="-I$PREFIX/include/cairo" 
  CAIRO_LIBS=$PREFIX/lib/libcairo.so 
  FONTCONFIG_CFLAGS="-I$PREFIX/include" 
  FONTCONFIG_LIBS=$PREFIX/lib/libfontconfig.so 
  FREETYPE_CFLAGS="-I$PREFIX/include/freetype2" 
  FREETYPE_LIBS=$PREFIX/lib/libfreetype.so 
  FREETYPE_CONFIG=$PREFIX/bin/freetype-config 
  ./configure --host=$HOST --build=$BUILD --prefix=$PREFIX --without-x

Edit Makefile:

Delete from the SUBDIRS var the directory ‘examples’

Edit tests/Makefile:

Add GLIB_LIBS to the LIBS variable:

LIBS = $(GLIB_LIBS)

Compile and install:

$ make
$ make install


Compiling GTK+ 2.12.11

If DirectFB is in PREFIX/../,
edit the files directfb.pc, direct.pc and fusion.pc in PREFIX/../lib/pkgconfig

Set the prefix var to the following value:

prefix=/opt/oe/STM/STLinux-2.2/devkit/sh4/target/usr

Search for the texts “Can’t link to Pango”, “Can’t find cairo-ps.h” and “Can’t find cairo-pdf.h”.
Remove the following code that appears a couple of lines below the searched texts:

 { (exit 1); exit 1; };

Configure:

$ BASE_DEPENDENCIES_CFLAGS="-I$PREFIX/include 
  -I$PREFIX/lib/glib-2.0/include -I$PREFIX/include/glib-2.0 
  -I$PREFIX/include/pango-1.0 
  -I$PREFIX/include/cairo 
  -I$PREFIX/include/atk-1.0" 
BASE_DEPENDENCIES_LIBS="-L$PREFIX/lib 
  $PREFIX/lib/libglib-2.0.so 
  $PREFIX/lib/libgobject-2.0.so $PREFIX/lib/libgmodule-2.0.so 
  $PREFIX/lib/libfontconfig.so $PREFIX/lib/libxml2.so" 
GLIB_CFLAGS="-I$PREFIX/include 
  -I$PREFIX/lib/glib-2.0/include 
  -I$PREFIX/include/glib-2.0" 
GLIB_LIBS="-L$PREFIX/lib 
  $PREFIX/lib/libglib-2.0.so 
  $PREFIX/lib/libgobject-2.0.so 
  $PREFIX/lib/libgmodule-2.0.so 
  $PREFIX/lib/libfontconfig.so 
  $PREFIX/lib/libxml2.so" 
PANGO_CFLAGS="-I$PREFIX/include/pango-1.0" 
PANGO_LIBS="-L$PREFIX/lib 
  $PREFIX/lib/libpango-1.0.so 
  $PREFIX/lib/libpangoft2-1.0.so 
  $PREFIX/lib/libpangocairo-1.0.so" 
GDK_DEP_CFLAGS="-pthread -I$PREFIX/include/glib-2.0 
  -I$PREFIX/lib/glib-2.0/include 
  -I$PREFIX/include/pango-1.0 
  -I$PREFIX/include/cairo 
  -I$PREFIX/include 
  -D_REENTRANT -D_GNU_SOURCE 
  -I$PREFIX/../include 
  -I$PREFIX/../include/directfb" 
GDK_DEP_LIBS="-L$PREFIX/lib -lpthread -ldl -lpangocairo-1.0 
  -lpango-1.0 -lcairo -lgobject-2.0 -lgmodule-2.0 -lglib-2.0 -lpng12 -lm 
  $PREFIX/../lib/libdirectfb.so 
  $PREFIX/../lib/libdirect.so 
  $PREFIX/../lib/libfusion.so" 
GDK_PIXBUF_DEP_CFLAGS="-pthread -I$PREFIX/include/glib-2.0 
  -I$PREFIX/lib/glib-2.0/include 
  -I$PREFIX/include 
  -I$PREFIX/../include" 
GDK_PIXBUF_DEP_LIBS="-L$PREFIX/lib 
  -lgmodule-2.0 -ldl -lgobject-2.0 -lglib-2.0 -lpng12 -lm" 
GTK_DEP_CFLAGS="-pthread -I$PREFIX/include/glib-2.0 
  -I$PREFIX/lib/glib-2.0/include 
  -I$PREFIX/include/pango-1.0 
  -I$PREFIX/include/cairo 
  -I$PREFIX/include -D_REENTRANT -D_GNU_SOURCE 
  -I$PREFIX/../include/directfb 
  -I$PREFIX/include/atk-1.0 
  -I$PREFIX/../include" 
GTK_DEP_LIBS="-L$PREFIX/lib 
  -lpangocairo-1.0 -lpango-1.0 -latk-1.0 -lgobject-2.0 -lgmodule-2.0 
  -ldl -lglib-2.0 -lcairo -lpng12 -lm 
  $PREFIX/../lib/libdirectfb.so 
  $PREFIX/../lib/libdirect.so 
  $PREFIX/../lib/libfusion.so" 
GDK_EXTRA_CFLAGS="-I$PREFIX/../include" 
GDK_EXTRA_LIBS="-L$PREFIX/../lib -lz -lpthread -ldl 
  $PREFIX/../lib/libdirectfb.so 
  $PREFIX/../lib/libdirect.so 
  $PREFIX/../lib/libfusion.so" 
./configure --host=$HOST --build=$BUILD --prefix=$PREFIX 
--with-gdktarget=directfb --without-libtiff --without-libjpeg 
--disable-glibtest --disable-largefile --disable-modules 
--with-included-loaders=gif,png,xpm

Edit gtk/Makefile:

Add to the GTK_DEP_LIBS var the following value:

 -lfontconfig -lfreetype

Remove the linking line of the rule gtk-query-immodules-2.0$(EXEEXT).
Warning: This means that we won’t have this command available in the target.

#$(LINK)

Dangerous/ugly step:

GTK needs a cairo-pdf/ps printing support for compiling,
but it’s unlikely that PDF/PS will be needed in an embedded system.
There is no flag to compile it without this setting.
There are some patches in development to solve this issue,
meanwhile it was compiled without the cairo-pdf support by doing
the following very ugly and dangerous step.
If you want to add to add PDF/PS support you can try Poppler.

Edit the files:

* gtk/gtkprintoperation.c
* gtk/gtkprintoperation-unix.c
* modules/printbackends/lpr/gtkprintbackendlpr.c
* modules/printbackends/file/gtkprintbackendfile.c

Comment the lines in all these files that contains the following includes or function calls:

#include 
#include 
cairo_pdf_surface_set_size()
cairo_pdf_surface_create()
cairo_ps_surface_create_for_stream()

Compile and install:

$ make
$ make install

That’s it. Feel free to contact for any comment/idea/hint if you have any problem or want to improve this procedure.

Additional notes

If you want to include libjpeg you new to remove the option –without-libjpeg and add it to the option –with-included-loaders=gif,png,xpm,jpeg

86 thoughts on “Cross-compiling GTK+ over DirectFB v0.2

  1. Ali

    Hi,

    Followed the New procedure .Some how getting stuck at gtk+ compilation…Ihave noticed a strange behavior.Weni configured it first it gave a different error for Pango not found .But when i tied to configure it sencond time .I got Glib error.Though it was identitfed the first time.

    checking pkg-config is at least version 0.16… yes
    checking for GLIB – version >= 2.13.5… no
    *** Could not run GLIB test program, checking why…
    *** The test program failed to compile or link. See the file config.log for the
    *** exact error that occured. This usually means GLIB is incorrectly installed.
    configure: error:
    *** GLIB 2.13.5 or better is required. The latest version of
    *** GLIB is always available from ftp://ftp.gtk.org/pub/gtk/.

    Regards
    Ali

    Reply
  2. paguilar

    Hi,

    Check your env vars, specially PKG_CONFIG_PATH.
    Sometimes when you get strange behaviour it’s better to untar the package and start again.

    Regards.

    Reply
  3. goralf

    Hi paguilar,
    When i configing the cairo-1.6.4, i have the issue:
    hecking zlib.h presence… yes
    checking for zlib.h… yes
    checking for sh4-linux-pkg-config… no
    checking for pkg-config… /usr/bin/pkg-config
    checking pkg-config is at least version 0.9.0… yes
    checking for pixman… no
    configure: error: pixman >= 0.10.0 is required
    (http://cairographics.org/releases/)
    [root@sha-jasonliang cairo-1.6.4]# cd ../

    And did you use the pixman package?
    Thanks!

    Reply
  4. Ali

    Hi Goralf,

    I had this problem . I have installed pixman-0.11.2 to overcome this problem.

    Regards
    Ali

    Reply
  5. paguilar

    Hi,

    It seems strange. I didn’t have this problem because pixman is included in all stable versions of Cairo like 1.6.4.

    Regards.

    Reply
  6. Ali

    Hi Paguliar,

    Some strange problems with GTK+ are cropping up everytime.

    May be if u dont mind can u explain it form the scrath ,I mean from the installation of STlinux and its package to the gtk+.That will be very kind of you.Because it’s been almost fortnight i m trying to get thing up and running.

    regards

    Reply
  7. Ali

    Hi Goralf,

    Did u successfully built and installed GTK+ also.If so pls shed some light on it.

    Regards

    Reply
  8. goralf

    Hi Ali,
    Yes, but don’t test.And what matters do you meet now?

    Reply
  9. Ali

    Hi Peguliar / Goralf,

    I am getting stuck at the configuration and build of GTk+ library. Something or other creeps up.May be i have to test it by clean the stlinux and the stgfb and reinstalling everthing from scratch.

    I am getting this error.

    checking pkg-config is at least version 0.16… yes
    checking for GLIB – version >= 2.13.5… no
    *** Could not run GLIB test program, checking why…
    *** The test program failed to compile or link. See the file config.log for the
    *** exact error that occured. This usually means GLIB is incorrectly installed.
    configure: error:
    *** GLIB 2.13.5 or better is required. The latest version of
    *** GLIB is always available from ftp://ftp.gtk.org/pub/gtk/.

    Did u cleaned everhting i mean even stlinux and stgfb package and re installed .

    Regards
    Ali

    Reply
  10. goralf

    Hi Ali,
    Yes, i changed to a new stlinux environment on another host.From your error msg, maybe that GLIB was installed with issue.

    Reply
  11. Ali

    Hi,

    Finally i was able to configure GTK+.But during build it’s giving error .

    make gtk-update-icon-cache
    make[3]: Entering directory `/opt/gtk+-2.12.11/gtk’
    make[3]: `gtk-update-icon-cache’ is up to date.
    make[3]: Leaving directory `/opt/gtk+-2.12.11/gtk’
    no –force –ignore-theme-index
    –source builtin_icons stock-icons > gtkbuiltincache.h.tmp &&
    mv gtkbuiltincache.h.tmp gtkbuiltincache.h
    /bin/sh: no: command not found
    make[2]: *** [gtkbuiltincache.h] Error 127
    make[2]: Leaving directory `/opt/gtk+-2.12.11/gtk’
    make[1]: *** [all-recursive] Error 1
    make[1]: Leaving directory `/opt/gtk+-2.12.11′
    make: *** [all] Error 2

    Were am i messing ?

    Regards

    Reply
  12. Ali

    Hi,

    GTK+ makefile is trying to run this statement on bash

    $(gtk_update_icon_cache_program) –force –ignore-theme-index –source builtin_icons stock-icons > gtkbuiltincache.h.tmp
    && mv gtkbuiltincache.h.tmp gtkbuiltincache.h

    where as :

    gtk_update_icon_cache_program is set as no.

    so there is error :

    /bin/sh: no: command not found

    what can be done to solve this issue.

    Regards

    Reply
  13. Ali

    Hi Peguliar,

    You have asked to remove a line from the makefile for GTK+

    “Remove the linking line of the rule gtk-query-immodules-2.0$(EXEEXT).

    Can u explain what exactly and which line i should remove in the make file (gtk/Makefile:).

    shall i remove this line :
    (1) bin_PROGRAMS = gtk-query-immodules-2.0$(EXEEXT)
    gtk-update-icon-cache$(EXEEXT)

    or shall i remove this line :

    (2) $(LINK) $(gtk_query_immodules_2_0_LDFLAGS)
    $(gtk_query_immodules_2_0_OBJECTS)
    $(gtk_query_immodules_2_0_LDADD) $(LIBS)

    Regards

    Reply
  14. paguilar

    Hi Ali,

    You should comment number (2) of your previous post where it links gtk-query-immodules

    gtk-query-immodules-2.0$(EXEEXT): $(gtk_query_immodules_2_0_OBJECTS) $(gtk_query_immodules_2_0_DEPENDENCIES)
        @rm -f gtk-query-immodules-2.0$(EXEEXT)
        #$(LINK) $(gtk_query_immodules_2_0_LDFLAGS) $(gtk_query_immodules_2_0_OBJECTS) $(gtk_query_immodules_2_0_LDADD) $(LIBS)
    

    I didn’t have problems with gtk_update_icon_cache_program as you mention in comment #13. It seems that the first part of the command was removed. Check if you didn’t remove it by mistake.

    Regards.

    Reply
  15. Ali

    Hi Paguilar.

    I was able to build the GTk+ package and install it in target ROOTFS.But when i booted the board over nfs and tried to run gtk-demo it gave an error.

    ————————————————————–
    root@LDDE22_ALi:/# gtk-demo
    gtk-demo: error while loading shared libraries: libgdk_pixbuf-2.0.so.0: cannot open shared object file: No such file or directory
    ————————————————————–
    Regards

    Reply
  16. paguilar

    Hi Ali,

    You can do:

    • Run in the target ldconfig -v
    • Edit all the .la files in $PREFIX. Change all the paths that have PREFIX (/opt/…) to /usr/local/…

    I haven’t tested the second one, but it should work.

    Regards,

    Reply
  17. Ali

    Hi Paguliar,

    I have done the chnages to .la files in $PERIX .And then did ldconfig -v .After that i ran the gtk-demo.some how i got this error.

    ———————————————————–
    root@LDDE22_ALi:/# gtk-demo

    =======================|DirectFB 1.0.0 ==========================
    (c) 2001-2007 The DirectFB Organization (directfb.org)
    (c) 2000-2004 Convergence (integrated media) GmbH
    ————————————————————

    (*) DirectFB/Core: Single Application Core. (2007-12-07 13:08)
    (*) Direct/Thread: Running ‘VT Switcher’ (CRITICAL, 310)…
    (*) Direct/Thread: Running ‘LiRC Input’ (INPUT, 311)…
    (*) DirectFB/Input: LIRC Device 0.2 (directfb.org)
    (*) Direct/Thread: Running ‘PS/2 Input’ (INPUT, 316)…
    (*) DirectFB/Input: IMPS/2 Mouse 1.0 (directfb.org)
    (*) Direct/Thread: Running ‘Keyboard Input’ (INPUT, 317)…
    (*) DirectFB/Input: Keyboard 0.9 (directfb.org)
    (!) DirectFB/gfxdrivers/stgfx: FB file descriptor = 3
    (*) DirectFB/Graphics: ST Microelectronics BDisp 0.99 (ST Microelectronics)
    (*) DirectFB/Core/WM: Default 0.3 (directfb.org)

    (gtk-demo:307): Gdk-CRITICAL **: gdk_drawable_set_colormap: assertion `cmap == NULL || gdk_drawable_get_depth (drawable) == cmap->visual->depth’ failed
    (*) Direct/Thread: Running ‘EventBufferFeed’ (MESSAGING, 318)…

    (gtk-demo:307): Pango-CRITICAL **: No fonts found:
    This probably means that the fontconfig
    library is not correctly configured. You may need to
    edit the fonts.conf configuration file. More information
    about fontconfig can be found in the fontconfig(3) manual
    page and on http://fontconfig.org

    (gtk-demo:307): Pango-CRITICAL **: No modules found:
    No builtin or dynamically loaded modules were found.
    PangoFc will not work correctly.
    This probably means there was an error in the creation of:
    ‘/opt/STM/STLinux-2.2/devkit/sh4/target/usr/local/etc/pango/pango.modules’
    You should create this file by running:
    pango-querymodules > ‘/opt/STM/STLinux-2.2/devkit/sh4/target/usr/local/etc/pango/pango.modules’

    (gtk-demo:307): Pango-WARNING **: failed to find shape engine, expect ugly output. engine-type=’PangoRenderFc’, script=’latin’

    (gtk-demo:307): Pango-CRITICAL **: No fonts found:
    This probably means that the fontconfig
    library is not correctly configured. You may need to
    edit the fonts.conf configuration file. More information
    about fontconfig can be found in the fontconfig(3) manual
    page and on http://fontconfig.org

    (gtk-demo:307): Gdk-DirectFB-WARNING **: gdk_display_request_selection_notification Unimplemented function

    (gtk-demo:307): Gdk-DirectFB-WARNING **: gdk_window_set_keep_above() not implemented.

    (gtk-demo:307): Gdk-DirectFB-WARNING **: gdk_window_set_keep_below() not implemented.

    ** (gtk-demo:307): WARNING **: Cannot find demo data file “appwindow.c”
    ——————————————————————-

    and on the Tv i see a window bieng displayed .But with junk characters on windows.

    what exactly is wrong here.

    Regards
    Ali
    ———————————————————–
    ***I was thinking u should allow files attachement on this blog .so that we can share snapshots of output display and other files as well. or some way to post images / pictures
    ————————————————————-

    Reply
  18. paguilar

    Hi Ali,

    You have to create the pango.modules file:

    > pango-querymodules > /usr/local/etc/pango/pango.modules
    

    Btw, check this post https://paguilar.org/?p=10

    for formatting the code. In this way is easier to read it.

    I’ll have a look at the attchmnt uploading. The default installation of the blog software doesn’t allow it. I have to search a plugin…

    Regards.

    Reply
  19. Ali

    Hi ,

    I did the abouve suggested step .But it says file doss not exist.
    ———————————————————
    root@LDDE22_ALi:~# pango-querymodules > /usr/local/etc/pango/pango.modules
    -bash: /usr/local/etc/pango/pango.modules: No such file or directory

    ———————————————————-

    The above link is asking user name and pwd!!!!!!!!!!

    Regards
    Ali

    Reply
  20. paguilar

    Hi Ali,

    The pango-querymodules program works for me in the target.
    If you only type the program name you should see in the terminal something like this:

    # Pango Modules file
    # Automatically generated file, do not edit
    #
    # ModulesPath = /opt/oe/STM/STLinux-2.2/devkit/sh4/target/usr/local/lib/pango/1.6.0/modules
    #
    /opt/oe/STM/STLinux-2.2/devkit/sh4/target/usr/local/lib/pango/1.6.0/modules/pango-basic-fc.so BasicScriptEngineFc PangoEngineShape PangoRenderFc latin:* cyrillic:* greek:* armenian:* georgian:* runic:* ogham:* bopomofo:* cherokee:* coptic:* deseret:* ethiopic:* gothic:* han:* hiragana:* katakana:* old-italic:* canadian-aboriginal:* yi:* braille:* cypriot:* limbu:* osmanya:* shavian:* linear-b:* ugaritic:* glagolitic:* cuneiform:* phoenician:* common:
    /opt/oe/STM/STLinux-2.2/devkit/sh4/target/usr/local/lib/pango/1.6.0/modules/pango-indic-fc.so devaScriptEngineFc PangoEngineShape PangoRenderFc devanagari:*
    ...
    
    

    Btw, I corrected the link in comment #20. Check it for formatting code.

    Regards.

    Reply
  21. goralf

    Hi Paguilar,
    When i run the gtk-demo, i have the error:
    root@goral:/root_STFAE# gtk-demo
    gtk-demo: symbol lookup error: /usr/local/lib/libgtk-directfb-2.0.so.0: undefined symbol: g_hash_table_ref
    root@goral:/root_STFAE#

    Can you tell me what’s about this error?

    Thanks!

    Reply
  22. paguilar

    Hi goralf,

    This happens because when gtk-demo is executed it tries to load its shared libraries (glib, pango and so on), but the dynamic loader doesn’t know where they are.

    You can solve doing this:

    > ld.config -v
    

    if this doesn’t work, add the /usr/local/lib directory to its path. This is done in the file /etc/ld.so.conf.

    Regards.

    Reply
  23. goralf

    Hi Paguilar,
    I make sure the /usr/local/lib directory in it’s path.And i run the ldconfig -v on target,but the error is still.As the error msg, it seems that there is issue in the /usr/local/lib/libgtk-directfb-2.0.so.0 .

    Reply
  24. goralf

    Hi Paguilar,
    The following is the ldd msg:
    root@goral:/root_STFAE# ldd -d /usr/local/bin/gtk-demo
    undefined symbol: g_hash_table_ref (/usr/local/lib/libgtk-directfb-2.0.so.0)
    undefined symbol: g_hash_table_unref (/usr/local/lib/libgtk-directfb-2.0.so.0)
    libgdk_pixbuf-2.0.so.0 => /usr/local/lib/libgdk_pixbuf-2.0.so.0 (0x29584000)
    libgdk-directfb-2.0.so.0 => /usr/local/lib/libgdk-directfb-2.0.so.0 (0x295b7000)
    libgtk-directfb-2.0.so.0 => /usr/local/lib/libgtk-directfb-2.0.so.0 (0x2963d000)
    libdirectfb-1.0.so.0 => /usr/lib/libdirectfb-1.0.so.0 (0x299fb000)
    libfusion-1.0.so.0 => /usr/lib/libfusion-1.0.so.0 (0x29a6b000)
    libdirect-1.0.so.0 => /usr/lib/libdirect-1.0.so.0 (0x29a83000)
    libpthread.so.0 => /lib/libpthread.so.0 (0x29aa5000)
    libpangocairo-1.0.so.0 => /usr/local/lib/libpangocairo-1.0.so.0 (0x29acd000)
    libpangoft2-1.0.so.0 => /usr/local/lib/libpangoft2-1.0.so.0 (0x29ae8000)
    libpango-1.0.so.0 => /usr/lib/libpango-1.0.so.0 (0x29b22000)
    libatk-1.0.so.0 => /usr/lib/libatk-1.0.so.0 (0x29b70000)
    libgobject-2.0.so.0 => /usr/lib/libgobject-2.0.so.0 (0x29b9c000)
    libgmodule-2.0.so.0 => /usr/lib/libgmodule-2.0.so.0 (0x29bdd000)
    libglib-2.0.so.0 => /usr/lib/libglib-2.0.so.0 (0x29bf0000)
    libcairo.so.2 => /usr/local/lib/libcairo.so.2 (0x29c98000)
    libpixman-1.so.0 => /usr/local/lib/libpixman-1.so.0 (0x29cf9000)
    libpng12.so.0 => /usr/lib/libpng12.so.0 (0x29d3c000)
    libfontconfig.so.1 => /usr/X11R7/lib/libfontconfig.so.1 (0x29d80000)
    libxml2.so.2 => /usr/lib/libxml2.so.2 (0x29dc5000)
    libdl.so.2 => /lib/libdl.so.2 (0x29f0b000)
    libm.so.6 => /lib/libm.so.6 (0x29f1f000)
    libfreetype.so.6 => /usr/lib/libfreetype.so.6 (0x29faa000)
    libz.so.1 => /usr/lib/libz.so.1 (0x2a02b000)
    libc.so.6 => /lib/libc.so.6 (0x2a04c000)
    /lib/ld-linux.so.2 (0x29556000)
    libexpat.so.1 => /usr/lib/libexpat.so.1 (0x2a190000)
    root@goral:/root_STFAE#
    It seems that the glib path is wrong.

    Reply
  25. paguilar

    Hi goralf,

    Check the version of your glib, I remember I had the same problem with other software (Swfdec) because I was not using the latest glib version. May be you linked GTK+ against the already provided glib located in /usr/lib instead of the new one that should be in /usr/local/lib.

    Regards.

    Reply
  26. goralf

    Hi Paguilar,
    The version is same as yours.I find some libs path all is in /usr/lib(libpng12.so.0,libpng12.so.0,glib,libfontconfig.so.1,libfreetype.so.6 etc).
    But some is right(libcairo.so.2,libpangoft2-1.0.so.0).
    It’s so strange!

    Reply
  27. goralf

    Hi Paguilar,
    Which .la files in $PREFIX need to be modified?The .la files of subdir of $PREFIX need to be modified?
    Thanks!

    Reply
  28. Ali

    Hi Paguilar,

    1) First of all the file (pango.modules)is not being created.I created the file manually in /usr/local/etc/pango/ directory and then executed the command
    > “pango-querymodules > /usr/local/etc/pango/pango.modules”

    2)Then i ran only the pango-querymodules :I go this output.The file does not have any contents except comments.

    # Pango Modules file
    # Automatically generated file, do not edit
    #
    # ModulesPath = /opt/STM/STLinux-2.2/devkit/sh4/target/usr/local/lib/pango/1.6.0/modules
    #

    3)and Morever The File contents of your pango.modules shows the path as “/opt/oe/STM…… “this path does not exist on the target

    4)If u See the log when i m running thr GTK-demo .IT says font not found.
    “(gtk-demo:311): Pango-CRITICAL **: No fonts found:”
    and
    “Pango-CRITICAL **: No modules found:”

    Regards

    Reply
  29. Ali

    Hi Paguliar,

    I want to compile a small gtk program.How do i do that on my host can just post a smaple application and its build procedure for cocoref.

    REgards

    Reply
  30. Ali

    Hi,
    THis is the msg i get when i run ldd -d gtk-demi.

     
    root@LDDE22_ALi:/usr/local/bin# ldd -d gtk-demo
            libgdk_pixbuf-2.0.so.0 => /usr/local/lib/libgdk_pixbuf-2.0.so.0 (0x29584000)
            libgdk-directfb-2.0.so.0 => /usr/local/lib/libgdk-directfb-2.0.so.0 (0x295b7000)
            libgtk-directfb-2.0.so.0 => /usr/local/lib/libgtk-directfb-2.0.so.0 (0x2963d000)
            libpangocairo-1.0.so.0 => /usr/local/lib/libpangocairo-1.0.so.0 (0x299fc000)
            libpangoft2-1.0.so.0 => /usr/local/lib/libpangoft2-1.0.so.0 (0x29a17000)
            libpango-1.0.so.0 => /usr/local/lib/libpango-1.0.so.0 (0x29a51000)
            libatk-1.0.so.0 => /usr/local/lib/libatk-1.0.so.0 (0x29aa5000)
            libgobject-2.0.so.0 => /usr/local/lib/libgobject-2.0.so.0 (0x29ad2000)
            libgmodule-2.0.so.0 => /usr/local/lib/libgmodule-2.0.so.0 (0x29b26000)
            libglib-2.0.so.0 => /usr/local/lib/libglib-2.0.so.0 (0x29b39000)
            libcairo.so.2 => /usr/local/lib/libcairo.so.2 (0x29c32000)
            libfontconfig.so.1 => /usr/X11R7/lib/libfontconfig.so.1 (0x29c93000)
            libfreetype.so.6 => /usr/local/lib/libfreetype.so.6 (0x29cd8000)
            libxml2.so.2 => /usr/local/lib/libxml2.so.2 (0x29d5a000)
            libdirectfb-1.0.so.0 => /usr/lib/libdirectfb-1.0.so.0 (0x29e9a000)
            libpixman-1.so.0 => /usr/local/lib/libpixman-1.so.0 (0x29f10000)
            libfusion-1.0.so.0 => /usr/lib/libfusion-1.0.so.0 (0x29f53000)
            libdirect-1.0.so.0 => /usr/lib/libdirect-1.0.so.0 (0x29f6b000)
            libpthread.so.0 => /lib/libpthread.so.0 (0x29f8e000)
            libdl.so.2 => /lib/libdl.so.2 (0x29fb6000)
            libpng12.so.0 => /usr/local/lib/libpng12.so.0 (0x29fca000)
            libz.so.1 => /usr/local/lib/libz.so.1 (0x29fff000)
            libm.so.6 => /lib/libm.so.6 (0x2a022000)
            libc.so.6 => /lib/libc.so.6 (0x2a0ad000)
            /lib/ld-linux.so.2 (0x29556000)
            libexpat.so.1 => /usr/lib/libexpat.so.1 (0x2a1f1000)
    

    Regards

    Reply
  31. goralf

    Hi Ali,
    I guess my error is caused by wrong glib path linked.And how you set the Environment?
    Thanks!

    Reply
  32. Ali

    Hi Goralf ,

    My environment variable are set according to the procedure mentioned in this blog.Nothing unusual.

    Regards

    Reply
  33. goralf

    Hi Ali,
    You set export PKG_CONFIG_PATH=$LD_LIBRARY_PATH/pkgconfig?
    This may be not sutiable to libdirectfb.

    Reply
  34. Ali

    Hi Goralf ,

    Initialy from glib till pango i have set .
    export PKG_CONFIG_PATH=$LD_LIBRARY_PATH/pkgconfig

    Then at the time of gtk+ i have set updated the path to .
    export PKG_CONFIG_PATH=$LD_LIBRARY_PATH/pkgconfig:$PREFIX/../lib/pkgconfig

    Regards

    Reply
  35. goralf

    Hi Ali,
    I try this, but issue is still.I want to know how you set the .pc files and .la files when compiling GTK.
    Thanks!

    Reply
  36. Ali

    Hi ,

    When i m installing font config .I m getting this warning.

    ***
    *** Warning: fonts.cache not built
    ***
    *** Generate this file manually on host system using fc-cache
    ***

    Isn’t the fonts cache suppose to be built .Na dif it is not built how does my application load the cache?

    Regards

    Reply
  37. paguilar

    Hi,

    Sorry for the late reply, I was on holidays for a few days.

    Regarding the linking problems that goralf had, I thought the following:

    It’s better to leave the PKG_CONFIG_PATH env var as it’s set at the beginning:

    $ export PKG_CONFIG_PATH=$LD_LIBRARY_PATH/pkgconfig
    

    and edit directfb.pc, direct.pc and fusion.pc as it’s described.

    This could lead to some problems like the ones you’re having because all the packages that you already installed (glib, pango, cairo…) were installed in $PREFIX, not in /usr/local. Therefore, when you execute any GTK+ based app it would search the libs in $PREFIX, that doesn’t exist.

    You can solve this by following the second option of comment #18 or (an ugly but quick option) by creating in your target a directory /opt/oe/STM/STLinux-2.2/devkit/sh4 and then a logical link:

    $ mkdir -p /opt/oe/STM/STLinux-2.2/devkit/sh4
    $ cd /opt/oe/STM/STLinux-2.2/devkit/sh4
    $ ln -s / target
    

    In this way anything that searches for $PREFIX will be found. This is NOT a clean way to do it, it’s just useful for a quick test. It’s much better if you edit the .la files.

    Hope this helps.
    Regards.

    Reply
  38. paguilar

    Hi Ali,

    The reason why my pango.modules have $PREFIX instead of /usr/local/… is described in comment #41.

    In any case, pango-querymodules should give you a non-empty answer. You can try, just for testing, to copy your pango.modules from your host to the target. At this point you would see a nice output.

    Just a thought: I think the only executable of pango-querymodules is the one that we install following this this procedure. Check that you’re executing this app and not another app that was provided by ST (I don’t remember if ST provides it in /usr).

    Hope this helps.
    Regards.

    Reply
  39. goralf

    Hi
    I solved the issue.That’s because i use the stfae tree, and the LD_LIBRARY_PATH in load_fb.sh is problem.I add the /usr/local/lib at the front of LD_LIBRARY_PATH.
    Thank you for help!

    Reply
  40. Ali

    Hi,

    I m trying to generate font cahe by giving this command

    $fc-cache -fs

    I m getting error
    _________________________________________________________
    ./fc-cache: symbol lookup error: ./fc-cache: undefined symbol: FcConfigGetCacheDirs
    _________________________________________________________

    regards

    Reply
  41. Ali

    Hi Paguilar,

    YOu have suggested to follow these steps before executing the gtk-demo application on target.

    * Run in the target ldconfig -v
    * Edit all the .la files in $PREFIX. Change all the paths that have PREFIX (/opt/…) to /usr/local/…

    But we have also edit the libdirectfb.la and libfusion.la in $prefix/../lib while building gtk+. DO i have to change there path as well to /usr/local /lib from /opt/STM/../usr/local.lib

    Regards

    Reply
  42. paguilar

    Hi Ali,

    I’ve never used fc-cache in the target, so I’ve never had this problem.

    If you created the ugly logical link that I mentioned in comment #41 you don’t need to change them because it will find them through this link.

    Regards.

    Reply
  43. Khaled

    I use a 64bit AMD host pc to cross compile GTK+ for STi7109 target board.
    I obtain the following error
    /opt/STM/STLinux-2.2/devkit/sh4/lib/gcc/sh4-linux/4.1.1/../../../../sh4-linux/bin/ld: skipping incompatible /opt/STM/STLinux-2.2/devkit/sh4/target/usr/lib/libpangoft2-1.0.so when searching for -lpangoft2-1.0
    /opt/STM/STLinux-2.2/devkit/sh4/lib/gcc/sh4-linux/4.1.1/../../../../sh4-linux/bin/ld: skipping incompatible /opt/STM/STLinux-2.2/devkit/sh4/target/usr/lib/libpangoft2-1.0.so when searching for -lpangoft2-1.0
    /opt/STM/STLinux-2.2/devkit/sh4/lib/gcc/sh4-linux/4.1.1/../../../../sh4-linux/bin/ld: skipping incompatible /opt/STM/STLinux-2.2/devkit/sh4/target/usr/lib/libpangoft2-1.0.so when searching for -lpangoft2-1.0
    /opt/STM/STLinux-2.2/devkit/sh4/lib/gcc/sh4-linux/4.1.1/../../../../sh4-linux/bin/ld: cannot find -lpangoft2-1.0
    collect2: ld a retourné 1 code d’état d’exécution

    It seems that this error occurs because the needed library was compiled on a 32bit system.
    If its the case what should I do?
    regards khaled

    Reply
  44. paguilar

    Hi Khaled,

    It seems that libpangoft2-1.0.so was compiled for an arch that is different from the one that you are compiling for.

    If this is the case, as you said, you would need to compile the whole chain (or at least pango) for the same arch: make sure that you are using the same compiler for all packages and installing them in the right path checking that the environment vars are correctly set.

    Another problem could be that the linker is looking for pango in the wrong path. This can be fixed setting the LD_CONFIG_PATH and PKG_CONFIG_PATH to the path in which you’re actually installing GTK+.

    Regards,

    Reply
  45. Pingback: Websites tagged "pthread" on Postsaver

  46. david

    Hi,

    I have a couple of lingering problems with gtk-demo:

    1. Gdk-CRITICAL **: gdk_drawable_set_colormap:

    Is a colormap required? I am using RGB16.

    2. Pango-CRITICAL **: No fonts found

    a) why when I do: pango-querymodules > …
    respond with “does not export Pango API” in all cases?
    lib/pango/1.6.0/modules/pango-basic-fc.so does not export Pango module API

    b) why does the fc-cache -fv
    respond 0 fonts in all cases?
    /etc/fonts: caching, new cache contents: 0 fonts, 2 dirs
    /etc/fonts/conf.avail: caching, new cache contents: 0 fonts, 0 dirs
    /etc/fonts/conf.d: caching, new cache contents: 0 fonts, 0 dirs
    /root/.fonts: caching, new cache contents: 0 fonts, 2 dirs
    /conf.avail: caching, new cache contents: 0 fonts, 0 dirs
    /conf.d: caching, new cache contents: 0 fonts, 0 dirs

    etc., etc,

    Regards, david

    Reply
  47. paguilar

    Hi David,

    Sorry for the late reply. I’ve been quite busy at work and at home.

    1. IIRC, this is a problem regarding only the DirectFB backend of GDK. The main developer of DirectFB posted a patch for GTK+ 2.12.9 that fixes a lot of things. May be if you try it you could solve your problem.

    2. I’ve never seen this problem before. You could check how you configured and installed Fontconfig and Pango and how you set the environment variables. May be the problem is more with Fontconfig (but it’s just a guess).

    Reply
  48. Kimi

    Hi Paguilar,
    The following error occured when install GTK+. Do you know where might be the problem?

    =========
    make[4]: Entering directory `/usr/gtk/src/gtk+-2.12.11/modules/input’
    /bin/sh ../../mkinstalldirs /usr/gtk/etc/gtk-2.0
    ../../gtk/gtk-query-immodules-2.0 > /usr/gtk/etc/gtk-2.0/gtk.immodules
    ../../gtk/gtk-query-immodules-2.0: symbol lookup error: /usr/gtk/lib/libcairo.so.2: undefined symbol: direct_config
    make[4]: *** [install-data-hook] Error 127
    make[4]: Leaving directory `/usr/gtk/src/gtk+-2.12.11/modules/input’
    make[3]: *** [install-data-am] Error 2
    make[3]: Leaving directory `/usr/gtk/src/gtk+-2.12.11/modules/input’
    make[2]: *** [install-am] Error 2
    make[2]: Leaving directory `/usr/gtk/src/gtk+-2.12.11/modules/input’
    make[1]: *** [install-recursive] Error 1
    make[1]: Leaving directory `/usr/gtk/src/gtk+-2.12.11/modules’
    make: *** [install-recursive] Error 1
    =========

    Regards,
    Kimi

    Reply
  49. paguilar

    Hi Kimi,

    Normally gtk-query-immodules-2.0 is not needed in an embedded system, so you can comment it:

    Remove the linking line of the rule gtk-query-immodules-2.0$(EXEEXT).

    If you still have problems or simply you want to have that program you can add the DirectFB linking flags -ldirectfb -ldirect -lfusion and their path, but I’m not sure this will be enough because I tried it some time ago and it didn’t work for me.

    Regards.

    Reply
  50. Iulian

    I tried to use your instructions to build GTK+ on a MIPS architectuire (a NXP chipset).
    Unfortunatelly i get stuck on cairo ./configure,
    which reports:
    configure: error: Cairo requires at least one font backend.
    Please install freetype and fontconfig, then try again:
    http://freetype.org/ http://fontconfig.org/

    I took a peek on config.log and found the followings:

    configure:27976: mipsel-linux-gcc -o conftest -g -O2 -I/rootfs/opt/gtkdfb/include/fontconfig conftest.c -lm /rootfs/opt/gtkdfb/lib/libfontconfig.so >&5
    /work/stb/STB225/toolchain/tuxbuilder-1.0/mipsel-unknown-linux-gnu/cross/bin/../lib/gcc/mipsel-unknown-linux-gnu/4.2.1/../../../../mipsel-unknown-linux-gnu/bin/ld: warning: libfreetype.so.6, needed by /rootfs/opt/gtkdfb/lib/libfontconfig.so, not found (try using -rpath or -rpath-link)
    /work/stb/STB225/toolchain/tuxbuilder-1.0/mipsel-unknown-linux-gnu/cross/bin/../lib/gcc/mipsel-unknown-linux-gnu/4.2.1/../../../../mipsel-unknown-linux-gnu/bin/ld: warning: libxml2.so.2, needed by /rootfs/opt/gtkdfb/lib/libfontconfig.so, not found (try using -rpath or -rpath-link)
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_PS_Font_Info’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `xmlCreatePushParserCtxt’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Init_FreeType’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_Sfnt_Name’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Load_Glyph’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Done_Face’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_Char_Index’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_Sfnt_Table’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `xmlSAX2GetLineNumber’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `xmlParseChunk’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Has_PS_Glyph_Names’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_Glyph_Name’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Select_Charmap’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `xmlCtxtGetLastError’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_Next_Char’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Load_Sfnt_Table’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Done_FreeType’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_Sfnt_Name_Count’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Select_Size’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_X11_Font_Format’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_BDF_Property’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `xmlFreeParserCtxt’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_Get_First_Char’
    /rootfs/opt/gtkdfb/lib/libfontconfig.so: undefined reference to `FT_New_Face’

    How do i fix this? Why doesn’t see the libfreetype.so.6 which is locate in the same lib file as all others (rootfs/opt/gtkdfb/lib)

    Reply
  51. paguilar

    Hi Iulian,

    This is a bit strange if you use the same packages versions, did you double-check that your environment vars (specifically LD_LIBRARY_PATH) are correctly configured?

    Reply
  52. Iulian

    Hi paguilar,

    all env’s are correct:

    export PREFIX=/rootfs/opt/gtkdfb
    export LD_LIBRARY_PATH=$PREFIX/lib
    export PKG_CONFIG_PATH=$LD_LIBRARY_PATH/pkgconfig

    all libs that i need are in $PREFIX/lib and all headers in $PREFIX/include

    I finally managed to build Cairo, Pango and finally GTK
    by setting CFLAGS and LDFLAGS.

    I don’t know why your steps didn’t work in my case.

    I must say that prior to embedded build i used your instructions to build the same packages on my PC (FC9) and i had no problem

    Reply
  53. tiny

    Hi Panguilar ,

    i need to cross compile mozilla for arm board . i have already cross compiled required libraries like gtk+2.12.9,glib,directfb,cairo etc.

    could you tell me whether there is any difference with the mozilla source code , ie can i compile the general code from mozilla.org or there is specific tar ball for mozilla supporting frame buffer(my requirement is frame buffer must be supported) .

    Reply
  54. ThanhDD

    Hi paguilar,

    Now I’m porting GTK for powerpc32.
    When I make GTK, it get error:

    powerpc-linux-gnu-gcc -g -O2 -Wall -o .libs/gtk-update-icon-cache updateiconcache.o -L/home/debian/ppc/lib ../gdk-pixbuf/.libs/libgdk_pixbuf-2.0.so -L/home/debian/ppc//lib /home/debian/ppc//lib/libgmodule-2.0.so -ldl /home/debian/ppc//lib/libgobject-2.0.so /home/debian/ppc//lib/libglib-2.0.so /home/debian/ppc/lib/libpng12.so -lz -lm -Wl,–rpath -Wl,/home/debian/ppc/lib -Wl,–rpath -Wl,/home/debian/ppc//lib
    creating gtk-update-icon-cache
    make[3]: Leaving directory `/home/debian/Software/gtk+-2.12.9/gtk’
    /usr/bin/gtk-update-icon-cache –force –ignore-theme-index
    –source builtin_icons stock-icons > gtkbuiltincache.h.tmp &&
    mv gtkbuiltincache.h.tmp gtkbuiltincache.h
    /usr/bin/gtk-update-icon-cache: error while loading shared libraries: /home/debian/ppc/lib/libgobject-2.0.so.0: ELF file data encoding not little-endian
    make[2]: *** [gtkbuiltincache.h] Error 127
    make[2]: Leaving directory `/home/debian/Software/gtk+-2.12.9/gtk’
    make[1]: *** [all-recursive] Error 1
    make[1]: Leaving directory `/home/debian/Software/gtk+-2.12.9′
    make: *** [all] Error 2

    Do you know this error? and how can I fix it?

    Thank you very much!

    Reply
  55. paguilar

    Hi,

    Normally when buuilding for an embedded system gtk-update-icon-cache is not needed, so you can comment the line in the gtk/Makefile when it tries to execute it:

    /usr/bin/gtk-update-icon-cache –force –ignore-theme-index 
    –source builtin_icons stock-icons > gtkbuiltincache.h.tmp && 
    mv gtkbuiltincache.h.tmp gtkbuiltincache.h
    

    Regards.

    Reply
  56. Richard

    hi,paguilar
    I have built mozilla-dfb-src successfully according to the procedure discribed in https://wiki.mozilla.org/Mobile/DFBPorting

    The content of my .directfbrc file is as the following:
    wm=default
    mode=800×600
    depth=16
    system=fbdev

    I run the gtk-demo correctly!but when I run ./firefox under mozilla-dfb-src/dist/bin directory.My machine went dead,and I have to reboot

    Did I miss anything?
    do you have any ideas about that?
    Thanks in advance!

    Reply
  57. paguilar

    Hi Richard,

    I haven’t tried firefox under DirectFB so I’m afraid I cannot be of help.

    It seems that display remains locked by DirectFB (pings and ssh should keep working). If gtk-demo runs correctly means that all the chain up to GTK+ works correctly. So it could be a firefox issue. May be a wrong snapshot?

    You could ask in the DirectFB development mailing list.

    Regards.

    Reply
  58. Richard

    thanks paguilar,for your remind.
    I’m trying to send a mail to DirectFB development mailing list.

    Reply
  59. Vinay

    Hi paguilar,

    I am trying to build GTK for MIPS.
    When i do a make for atk i get the following error:

    make all-recursive
    make[1]: Entering directory `/home/vinay/GTK_DFB/packages/packages_tar/atk-1.24.0′
    Making all in atk
    make[2]: Entering directory `/home/vinay/GTK_DFB/packages/packages_tar/atk-1.24.0/atk’
    glib-genmarshal –prefix=atk_marshal ./atkmarshal.list –header >> xgen-gmh
    && (cmp -s xgen-gmh atkmarshal.h || cp xgen-gmh atkmarshal.h)
    && rm -f xgen-gmh xgen-gmh~
    && echo timestamp > stamp-atkmarshal.h
    glib-genmarshal: error while loading shared libraries: /usr/local/Broadcom_GTK/lib/libglib-2.0.so.0: ELF file data encoding not little-endian
    make[2]: *** [stamp-atkmarshal.h] Error 127
    make[2]: Leaving directory `/home/vinay/GTK_DFB/packages/packages_tar/atk-1.24.0/atk’
    make[1]: *** [all-recursive] Error 1
    make[1]: Leaving directory `/home/vinay/GTK_DFB/packages/packages_tar/atk-1.24.0′
    make: *** [all] Error 2

    Please help me fix this error.

    Thanks a lot .

    Reply
  60. paguilar

    Hi Vinay,

    The problem is that Atk is using the libraries for your x86 host, not the ones for your mips target. Check that the environment variables are set correctly, specially LD_LIBRARY_PATH that must be set to your target’s rootfs.
    Another cause of this problem could be that you’re using a different Atk version. It’s better if you use the ones described here. They’re a bit out-dated, but they work!

    Regards.

    Reply
  61. Sachin

    Hi Paguilar,

    I am trying to build GTK for MIPS.
    When i do a make for atk i get the error what vinay was facing:
    Mine LD_LIBRARY_PATH=/usr/local/GTK_APP for mips
    Also i tried with the same version as mentioned above then also the same situation.
    While cross compilig glib that threw an error for iconv and gettext not found.
    Finally i cross compiled glib after cross compiling iconv and gettext.
    Please help me

    Reply
  62. paguilar

    Hi Sachin,

    Did you check that LD_LIBRARY_PATH=/usr/local/GTK_APP is the path where the libs for you target are?
    Eg. the glib that you just installed should be there.

    I hope this helps, otherwise I’m out of ideas at the moment.

    I’ve never had the need to compile iconv and gettext, may be because they were already installed in the target.

    Regards.

    Reply
  63. Sachin

    Hi Panguilar,

    MY environment variables are,
    export PREFIX=/usr/local/GTK_APP
    export LD_LIBRARY_PATH=$PREFIX/lib
    export PKG_CONFIG_PATH=$LD_LIBRARY_PATH/pkgconfig:$PKG_CONFIG_PATH
    export COMPILER2=mips-linux-uclibc-gcc
    export HOST=mips-linux-uclibc
    export BUILD=i386-linux
    export PKG_CONFIG=/usr/bin/pkg-config

    In my case glib-genmarshal is of little endian type from /usr/bin of linux pc.
    My LD_LIBRARY_PATH is /usr/local/GTK_APP/lib (which are all of big endian type).
    If i set environment variable PATH to tool chaine:/usr/local/GTK_APP/bin that shows error as glib-genmarshal
    cant execute binary file.

    This problem seems to be obvious as I try to execute BIG ENDIAN binary in LITTLE ENDIAN machine .

    I tried out aother way commenting “glib-genmarshal” in ATK Makefile . I did not face any problem.

    I then tried compiling GTK and faced that problem saying “ELF file data encoding not LITTLE ENDIAN ” same as in the case of ATK.
    Again in GTK I commented GEN_MARSHALL .
    Finally I got error saying

    /.libs/libgtk-directfb-2.0.so: undefined reference to `gtk_marshal_BOOLEAN__VOID’

    I feel that All these errors are because of glib libraries .

    Can you please help me in this regard

    Thanks in advance.

    Reply
  64. Sean

    Hey,
    I have been trying to follow your guide but I keep running into the following when making ATK –

    glib-genmarshal: error while loading shared libraries: /usr/TS7390GTKfb/lib/libglib-2.0.so.0: ELF file OS ABI invalid

    This tells me that the host version of glib-genmarshal can’t read the libglib that I just built because its for the target.
    So I set the PATH to the glib-genmarshal that was built while cross-compiling glib but the host can’t run that program because the binary is from ARM (my target board).

    From the web the only solution I can find is to unset the LD_LIBRARY_PATH while making ATK – but that seems wrong to me because ATK would then pick up the host version of GLIB, not newly built target version – and also without having LD_LIBRAY_PATH set to the lib of my development area – $PREFIX/lib – the make doesn’t know where to pick up the other libraries – in my case libfusion.

    Do you have a solution to this problem? I can only imagine that most would come across this if following the same procedure.
    Any help is much appreciated.

    Thanks,
    Sean.

    Reply
  65. paguilar

    Hi Sean,

    With atk-1.23.5 I didn’t have this problem. But I remember I have seen it before, although I don’t remember what I was compiling.

    A workaround to this problem could be to comment the line that calls glib-genmarshal. It’s not nice, but it shouldn’t create any side-effect.

    Another way for solving it is a bit tricky: start compiling atk as you are doing it, then when it gives the error move the sources to the target and let glib-genmarshal to execute, then take the sources back to the host and continue the compilation.
    I used this procedure for compiling for the first time swfdec.

    I hope this helps you.

    Reply
  66. Sean

    Hi,

    Thanks for your response to my question.
    I finally got over this issue – I used different versions of some of the libraries – and specifically I used the latest versions of GLIB and ATK, which overcame this issue.

    But I am having a similar issue with compiling the GTK+ library. I am getting the following error:

    /usr/bin/gtk-update-icon-cache: error while loading shared libraries: libgobject-2.0.so.0: ……

    From one of your previous posts I commented out the line in the makefile that is trying to do this operation and the make continued. But after this I got the following error, which I can’t fix:

    /usr/bin/gdk-pixbuf-csource: error while loading shared libraries: /usr/TS7390GTK//lib/libgio-2.0.so.0: ELF file OS ABI invalid

    So the problem now is with the gdk-pixbuf-csource binary of the host not being able to read the traget library.

    Have you come across this, and the big question is, do you have a solution?

    Thanks,
    Sean.

    Reply
  67. paguilar

    Hi Sean,

    It’s good to know that you solved the first problem.
    libgio is a relatively new lib that is part of glib. The last time I compiled GTK+ it did not exist, so I cannot tell you much about it. I don’t know the consequences if you comment out that line. May be you can execute that command in the target and then come back with the result to the host: it’s the same idea that I described in comment #71.

    I realized that it’s one year since this post so I have definitely to find some time to update this procedure.

    Regards.

    Reply
  68. Mohan

    i am running WebKit browser with gtk+directfb backend while unning i am getting following error.
    please can any one tell how to resolve this problem

    GtkLauncher:1006): Gdk-CRITICAL **: gdk_drawable_set_colormap: assertion `cmap == NULL || gdk_drawable_get_depth (drawable) == cmap->visual->depth’ failed
    (*) Direct/Thread: Started ‘EventBufferFeed’ (-1) [MESSAGING OTHER/OTHER 0/0] …

    (GtkLauncher:1006): Pango-CRITICAL **: No fonts found:
    This probably means that the fontconfig
    library is not correctly configured. You may need to
    edit the fonts.conf configuration file. More information
    about fontconfig can be found in the fontconfig(3) manual
    page and on http://fontconfig.org
    (!) [ 1006: 0.000] –> Caught signal 11 (at (nil), invalid address) <–
    (!!!) *** WARNING [still objects in ‘Window Pool’] *** [object.c:241 in fusion_object_pool_destroy()]
    (!!!) *** WARNING [still objects in ‘Layer Region Pool’] *** [object.c:241 in fusion_object_pool_destroy()]
    (!!!) *** WARNING [still objects in ‘Layer Context Pool’] *** [object.c:241 in fusion_object_pool_destroy()]
    (!!!) *** WARNING [still objects in ‘Surface Pool’] *** [object.c:241 in fusion_object_pool_destroy()]
    Aborted

    Reply
  69. paguilar

    Hi,
    If IIRC you need to copy some fonts to the target. You can get the fonts from your target. eg. from /usr/share/fonts/truetype/

    The directory where you will copy the fonts to is the one that you write in the fonts.conf file needed by fontconfig.

    Regards.

    Reply
  70. Wayne

    Hi,

    First off thanks for all the work on the site, I have found it extremely useful.

    I am having some problems with making libpng. I have followed your instructions work for word and I have had zero errors until I try to Make libpng, here is what is output to the screen.

    make all-am
    make[1]: Entering directory `/usr/arm-gtkdfb/src/libpng-1.2.29′
    /bin/sh ./libtool –tag=CC –mode=compile arm-none-linux-gnueabi-gcc -DHAVE_CONFIG_H -I. -DPNG_CONFIGURE_LIBPNG -g -O2 -MT libpng12_la-png.lo -MD -MP -MF .deps/libpng12_la-png.Tpo -c -o libpng12_la-png.lo `test -f ‘png.c’ || echo ‘./’`png.c
    libtool: compile: arm-none-linux-gnueabi-gcc -DHAVE_CONFIG_H -I. -DPNG_CONFIGURE_LIBPNG -g -O2 -MT libpng12_la-png.lo -MD -MP -MF .deps/libpng12_la-png.Tpo -c png.c -fPIC -DPIC -o .libs/libpng12_la-png.o
    In file included from png.c:13:
    png.h:440:18: error: zlib.h: No such file or directory
    In file included from png.h:444,
    from png.c:13:
    pngconf.h:1241: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘*’ token
    pngconf.h:1242: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘*’ token
    pngconf.h:1243: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘*’ token
    In file included from png.c:13:

    Followed by more similar to the last few lines there. My environment variables are sound as I would not have made it this far.

    Would recommend trying a different version? Or is there a fix that is know to you?

    Once again many thanks.

    Wayne

    Reply
  71. paguilar

    Hi,
    libng is not finding zlib, did you set this variable to ‘yes’?

    ac_cv_lib_z_zlibVersion=yes

    That version should work without problems. I’ve compiled more recent versions, but I haven’t test them yet. As soon as I test them I will publish the results.

    Sorry for the late reply, I’ve been quite busy lately.
    Regards.

    Reply
  72. James

    Hi paguilar,
    I run gtk-demo on my arm board with cross compile gtk+directfb libraries.
    But i got this message that I don’t know how to debug it.
    could you give me some hints?
    thanks.

    root@x /usr/jlib/bin$ ./gtk-demo
    commandline read: gtk-demo

    ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.2 |~~~~~~~~~~~~~~~~~~~~~~~~~~
    (c) 2001-2009 The world wide DirectFB Open Source Community
    (c) 2000-2004 Convergence (integrated media) GmbH
    —————————————————————-

    (*) DirectFB/Core: Multi Application Core. (2009-12-03 07:16)
    (*) Direct/Memcpy: Using libc memcpy()
    (*) Fusion/Init: Builtin Implementation is still experimental! Crash/Deadlocks might occur!
    (*) Fusion/SHM: Using MADV_REMOVE (2.6.28.0 >= 2.6.19.2)
    (*) Direct/Thread: Started ‘Fusion Dispatch’ (2091) [MESSAGING OTHER/OTHER 0/0] …
    (*) Direct/Thread: Started ‘VT Switcher’ (2093) [CRITICAL OTHER/OTHER 0/0] …
    (*) Direct/Thread: Started ‘VT Flusher’ (-1) [DEFAULT OTHER/OTHER 0/0] …
    (*) DirectFB/FBDev: Found ‘DISP3 BG’ (ID 0) with frame buffer at 0x93200000, 1800k (MMIO 0x00000000, 0k)
    (*) Direct/Thread: Started ‘Linux Input’ (2096) [INPUT OTHER/OTHER 0/0] …
    (*) DirectFB/Input: CHESEN USB Keyboard (1) 0.1 (directfb.org)
    (*) Direct/Thread: Started ‘Linux Input’ (2097) [INPUT OTHER/OTHER 0/0] …
    (*) DirectFB/Input: CHESEN USB Keyboard (2) 0.1 (directfb.org)
    (*) Direct/Thread: Started ‘Linux Input’ (2098) [INPUT OTHER/OTHER 0/0] …
    (*) DirectFB/Input: USB Optical Mouse (3) 0.1 (directfb.org)
    (*) Direct/Thread: Started ‘PS/2 Input’ (2099) [INPUT OTHER/OTHER 0/0] …
    (*) DirectFB/Input: IMPS/2 Mouse 1.0 (directfb.org)
    (*) Direct/Thread: Started ‘Keyboard Input’ (2100) [INPUT OTHER/OTHER 0/0] …
    (*) DirectFB/Input: Keyboard 0.9 (directfb.org)
    (*) DirectFB/Graphics: Generic Software Rasterizer 0.6 (directfb.org)
    (*) DirectFB/Core/WM: Default 0.3 (directfb.org)

    (gtk-demo:2090): Gdk-CRITICAL **: gdk_drawable_set_colormap: assertion `cmap == NULL || gdk_drawable_get_depth (drawable) == cmap->vi
    sual->depth’ failed
    (*) Direct/Thread: Started ‘EventBufferFeed’ (2101) [MESSAGING OTHER/OTHER 0/0] …
    (!) [ 2090: 1.439] –> Caught signal 11 (at 0x28, invalid address) <–
    (!!!) *** WARNING [still objects in ‘Window Pool’] *** [object.c:241 in fusion_object_pool_destroy()]
    (!!!) *** WARNING [still objects in ‘Layer Region Pool’] *** [object.c:241 in fusion_object_pool_destroy()]
    (!!!) *** WARNING [still objects in ‘Layer Context Pool’] *** [object.c:241 in fusion_object_pool_destroy()]
    (!!!) *** WARNING [still objects in ‘Surface Pool’] *** [object.c:241 in fusion_object_pool_destroy()]
    (!) Direct/Thread: Canceling ‘Fusion Dispatch’ (2091)!
    Aborted

    Reply
  73. paguilar

    Hi James,
    Which version of GTK+ are you using?
    May be you can try a different version (older?).
    Btw, I haven’t tested the latest GTK+ with DirectFB 1.4. I hope to have time for testing them before this year ends.

    Reply
  74. James

    Hi Paguilar,
    I tried gtk+ 2.16.6 and 2.19.0 ,and got the same error.
    I will try another older version.
    Thanks for the suggestion.

    Reply
  75. Hong

    Hi~

    Im making gtk+

    # make


    make[3]: Entering directory `/home/nais/mini2440/src2/gtk+-2.12.11/gtk’
    if arm-linux-gcc -DHAVE_CONFIG_H -I. -I. -I.. -DG_LOG_DOMAIN=”Gtk” -DGTK_LIBDIR=”/sdcard/lib” -DGTK_DATADIR=”/sdcard/share” -DGTK_DATA_PREFIX=”/sdcard” -DGTK_SYSCONFDIR=”/sdcard/etc” -DGTK_VERSION=”2.12.11″ -DGTK_BINARY_VERSION=”2.10.0″ -DGTK_HOST=”arm-unknown-linux-gnu” -DGTK_COMPILATION -DGTK_PRINT_BACKENDS=”file,lpr” -DGTK_PRINT_PREVIEW_COMMAND=””evince –unlink-tempfile –preview –print-settings %s %f”” -I../gtk -I.. -I../gdk -I../gdk -I../gdk-pixbuf -I../gdk-pixbuf -DGDK_PIXBUF_DISABLE_DEPRECATED -DGDK_DISABLE_DEPRECATED -DGTK_FILE_SYSTEM_ENABLE_UNSUPPORTED -DGTK_PRINT_BACKEND_ENABLE_UNSUPPORTED -DG_DISABLE_CAST_CHECKS -pthread -D_REENTRANT -I/sdcard/include/glib-2.0 -I/sdcard/lib/glib-2.0/include -I/sdcard/include/pango-1.0 -I/sdcard/include/cairo -I/sdcard/include/pixman-1 -I/sdcard/include/freetype2 -I/sdcard/include -I/sdcard/include/directfb -I/sdcard/include/libpng12 -I/sdcard/include/atk-1.0 -D_REENTRANT -I/sdcard/include/cairo -I/sdcard/include/directfb -I/sdcard/include/pixman-1 -I/sdcard/include/freetype2 -I/sdcard/include -I/sdcard/include/libpng12 -g -O2 -Wall -MT updateiconcache.o -MD -MP -MF “.deps/updateiconcache.Tpo”
    -c -o updateiconcache.o `test -f ‘updateiconcache.c’ || echo ‘./’`updateiconcache.c;
    then mv -f “.deps/updateiconcache.Tpo” “.deps/updateiconcache.Po”;
    else rm -f “.deps/updateiconcache.Tpo”; exit 1;
    fi
    arm-none-linux-gnueabi-gcc: %s: No such file or directory
    arm-none-linux-gnueabi-gcc: %f”: No such file or directory
    cc1: error: unrecognized command line option “-funlink-tempfile”
    cc1: error: unrecognized command line option “-fpreview”
    cc1: error: unrecognized command line option “-fprint-settings”
    make[3]: *** [updateiconcache.o] Error 1
    make[3]: Leaving directory `/home/nais/mini2440/src2/gtk+-2.12.11/gtk’
    make[2]: *** [gtkbuiltincache.h] Error 2
    make[2]: Leaving directory `/home/nais/mini2440/src2/gtk+-2.12.11/gtk’
    make[1]: *** [all-recursive] Error 1
    make[1]: Leaving directory `/home/nais/mini2440/src2/gtk+-2.12.11′
    make: *** [all] Error 2

    …?

    Reply
  76. NAVI

    Hi Paguilar,

    I am trying to build gtk on directfb for MIPS target.

    First of all, I thought of building and testing the idea on desktop(ubuntu 9.10) and then take the same libs onto MIPS.

    I am building mainly 3 libs:
    cairo 1.8.8
    pango-1.26
    gtk+-2.18.4

    Other dependencies I am using from desktop.

    I can patch and build gtk.

    But I am facing problem in running the exmaples that come with gtk.

    I am trying to run examples/text/

    and getting following crash:-

    #0 0x0061099e in cairo_directfb_surface_create (dfb=0x806f658, dfbsurface=0x0) at cairo-directfb-surface.c:1916
    #1 0x00939a8a in _gdk_windowing_create_cairo_surface (drawable=0x80770f0, width=600, height=500) at gdkdrawable-directfb.c:1622
    #2 0x00932b7e in gdk_window_create_cairo_surface (drawable=0x8071150, width=600, height=500) at gdkwindow.c:4778
    #3 0x0090e192 in _gdk_drawable_create_cairo_surface (drawable=0x8071150, width=600, height=500) at gdkdraw.c:1904
    #4 0x00932c24 in gdk_window_ref_cairo_surface (drawable=0x8071150) at gdkwindow.c:4815
    #5 0x0090e471 in _gdk_drawable_ref_cairo_surface (drawable=0x8071150) at gdkdraw.c:1297
    #6 0x0093432b in gdk_window_clear_backing_region_direct (window=0x8071150, region=0x80b0940, send_expose=)
    at gdkwindow.c:4356
    #7 gdk_window_clear_region_internal (window=0x8071150, region=0x80b0940, send_expose=) at gdkwindow.c:4467
    #8 0x00934764 in gdk_window_clear_area_internal (window=0x8071150, x=, y=0, width=600, height=500,
    send_expose=0) at gdkwindow.c:4501
    #9 0x00934894 in IA__gdk_window_clear (window=0x8071150) at gdkwindow.c:4407
    #10 0x0093c578 in gdk_event_translate (event=) at gdkevents-directfb.c:773
    #11 dfb_events_process_window_event (event=) at gdkevents-directfb.c:160
    #12 0x0093cdfd in dfb_events_io_func (channel=0x807d470, condition=G_IO_IN, data=0x0) at gdkevents-directfb.c:233
    #13 0x009f7dab in ?? () from /lib/libglib-2.0.so.0
    #14 0x009c0e88 in g_main_context_dispatch () from /lib/libglib-2.0.so.0
    #15 0x009c4730 in ?? () from /lib/libglib-2.0.so.0
    #16 0x009c4b9f in g_main_loop_run () from /lib/libglib-2.0.so.0
    #17 0x003c3ef9 in IA__gtk_main () at gtkmain.c:1218
    #18 0x08049cd1 in main (argc=1, argv=0xbffff324) at text.c:183

    Can you suggest me how to tackle this crash ?

    Thanks & Regards,
    navi

    Reply
  77. paguilar

    Hi navi,
    Sorry for the late reply.
    I had a crash too when runnin gtk-demo after compiling recent versions like you, although I don’t remember right now the exact versions.

    May be you could try older versions. That what I’ll do before posting a v0.3 because recent versions crashes. Notice that I was testing in an SH arch, not x86.

    Reply
  78. paguilar

    Hi Hong,
    It seems that the arm preprocessor cc1 is not recognizing those options. If you don’t really need updateiconcache (and normally you don’t in an embedded system), you can comment it in the Makefile. I have done this before, it’s ugly but it works 😉
    And sorry for the late reply.

    Reply
  79. jack

    HI paguilar
    I have the same problem as Hong and i don’t know how to solve it . would you please make it clear? thanks

    Reply
    1. paguilar

      Hi Jack,
      Did you try what I answered to Hong?
      From my reply 2010/01/30: It seems that the arm preprocessor cc1 is not recognizing those options. If you don’t really need updateiconcache (and normally you don’t in an embedded system), you can comment it in the Makefile.
      Notice that the GTK+ version was quite old, like the reply. Current GTK+ versions could have changed a lot.

      Reply

Leave a Reply to Richard Cancel reply

Your email address will not be published. Required fields are marked *